Bcmwiki: Update: V1/V2 naming, remove ESP32/Pi distinction

2026-03-08T13:21:12Z

Update: V1/V2 naming, remove ESP32/Pi distinction

← Older revision		Revision as of 13:21, 8 March 2026
Line 1:		Line 1:
	== Serial Commands ~~(ESP32)~~ ==		== Serial Commands ==

	The ~~ESP32-based~~ bcMeter provides a USB serial debug interface for hardware diagnostics and manual control. Connect via USB-C at 115200 baud.		The bcMeter provides a USB serial debug interface for hardware diagnostics and manual control. Connect via USB-C at 115200 baud.

	~~'''Note:''' This applies to the '''ESP32 firmware''' only. The open-source [https://github.com/dahljo/bcmeter-dev bcmeter-dev] implementation uses standard Linux tools instead~~.

	=== Available Commands ===		=== Available Commands ===
Line 10:		Line 8:
	! Command !! Description		! Command !! Description
	\|-		\|-
	\| <code>led ~~<~~ch~~> <~~duty~~>~~</code> \|\| Set LED brightness. Channel 0–2 (880/520/370nm), duty 0–255.		\| <code>led <ch> <duty></code> \|\| Set LED brightness. Channel 0–2 (880/520/370nm), duty 0–255.
	\|-		\|-
	\| <code>pump ~~<~~duty~~>~~</code> \|\| Set pump PWM duty cycle (0–255).		\| <code>pump <duty></code> \|\| Set pump PWM duty cycle (0–255).
	\|-		\|-
	\| <code>adc</code> \|\| Test ADS1220 ADC detection and read current values.		\| <code>adc</code> \|\| Test ADS1220 ADC detection and read current values.
Line 20:		Line 18:
	\| <code>gps</code> \|\| GPS position report (lat, lon, altitude, satellites, HDOP).		\| <code>gps</code> \|\| GPS position report (lat, lon, altitude, satellites, HDOP).
	\|-		\|-
	\| <code>modem ~~<~~AT command~~>~~</code> \|\| Send raw AT command to SIM7080G modem.		\| <code>modem <AT command></code> \|\| Send raw AT command to SIM7080G modem.
	\|-		\|-
	\| <code>modemscan</code> \|\| Detect modem UART configuration.		\| <code>modemscan</code> \|\| Detect modem UART configuration.
Line 30:		Line 28:
	\| <code>scan</code> \|\| Scan for nearby WiFi networks.		\| <code>scan</code> \|\| Scan for nearby WiFi networks.
	\|-		\|-
	\| <code>connect ~~<~~ssid~~> <~~password~~>~~</code> \|\| Save WiFi credentials and connect.		\| <code>connect <ssid> <password></code> \|\| Save WiFi credentials and connect.
	\|-		\|-
	\| <code>ap</code> \|\| Switch to access point (hotspot) mode.		\| <code>ap</code> \|\| Switch to access point (hotspot) mode.
	\|-		\|-
	\| <code>storage</code> \|\| Show storage usage summary (~~LittleFS~~ + SD card).		\| <code>storage</code> \|\| Show storage usage summary (internal + SD card).
	\|-		\|-
	\| <code>export</code> \|\| Export all logs to SD card.		\| <code>export</code> \|\| Export all logs to SD card.

Bcmwiki: Wiki update: sync with manual and dev docs (2026-03)

2026-03-08T13:10:44Z

Wiki update: sync with manual and dev docs (2026-03)

New page

== Serial Commands (ESP32) ==

The ESP32-based bcMeter provides a USB serial debug interface for hardware diagnostics and manual control. Connect via USB-C at 115200 baud.

'''Note:''' This applies to the '''ESP32 firmware''' only. The open-source [https://github.com/dahljo/bcmeter-dev bcmeter-dev] implementation uses standard Linux tools instead.

=== Available Commands ===

{| class="wikitable"
! Command !! Description
|-
| <code>led <ch> <duty></code> || Set LED brightness. Channel 0–2 (880/520/370nm), duty 0–255.
|-
| <code>pump <duty></code> || Set pump PWM duty cycle (0–255).
|-
| <code>adc</code> || Test ADS1220 ADC detection and read current values.
|-
| <code>sps30</code> || Quick read from particulate matter sensor.
|-
| <code>gps</code> || GPS position report (lat, lon, altitude, satellites, HDOP).
|-
| <code>modem <AT command></code> || Send raw AT command to SIM7080G modem.
|-
| <code>modemscan</code> || Detect modem UART configuration.
|-
| <code>modemon</code> / <code>modemoff</code> || Power control for the modem.
|-
| <code>wifi</code> || Current WiFi status and IP address.
|-
| <code>scan</code> || Scan for nearby WiFi networks.
|-
| <code>connect <ssid> <password></code> || Save WiFi credentials and connect.
|-
| <code>ap</code> || Switch to access point (hotspot) mode.
|-
| <code>storage</code> || Show storage usage summary (LittleFS + SD card).
|-
| <code>export</code> || Export all logs to SD card.
|-
| <code>reset</code> || Reboot the device.
|-
| <code>help</code> || List all available commands.
|}

=== Usage Example ===

<pre>
# Connect via screen (macOS/Linux)
screen /dev/tty.usbmodem* 115200

# Or via minicom
minicom -D /dev/ttyACM0 -b 115200

# Check sensor readings
> adc
ADS1220 detected at SPI
Ch0 (Sen 880): 2.341V
Ch1 (Ref 880): 2.518V

# Manually control pump
> pump 80
Pump duty set to 80/255

# Check GPS
> gps
Fix: valid
Lat: 52.4631, Lon: 13.3069
Sats: 7, HDOP: 1.2
Alt: 48.3m, Speed: 0.0 km/h
</pre>

Serial commands - Revision history

Bcmwiki: Update: V1/V2 naming, remove ESP32/Pi distinction

Bcmwiki: Wiki update: sync with manual and dev docs (2026-03)