Difference between revisions of "Installation"

Latest revision as of 20:38, 8 March 2026

Template:Note

Recommended: Pre-configured microSD Card Image (V1)

Step 1: Download and Flash the Image

Download the bcMeter image file here
Unzip the downloaded file
Use Etcher to flash the image to your microSD card:
- Insert your microSD card
- Open Etcher and select the image
- Select your microSD card as target
- Click "Flash!" and wait for completion

Step 2: Boot and Connect

Insert the flashed microSD card into the Raspberry Pi
Power on the device
Wait approximately 2 minutes for boot
Connect to the WiFi network "bcMeter" with password: bcMeterbcMeter

Step 3: Configure

Open a browser and navigate to http://bcmeter-XXXX.local (where XXXX are the last 4 hex characters of the MAC address, shown on the device label)
The bcMeter interface will appear
Follow on-screen instructions

Advanced: Manual Setup via SSH (V1)

Use the Raspberry Pi Imager to write Raspberry OS 64-bit LITE to the microSD card. Do not install the Desktop variant.

Configure with username bcmeter and password bcmeter.org. Enable SSH and WiFi.

SSH Installation

ssh bcmeter@bcMeter
# or: ssh bcmeter@bcMeter.local

# Download and run installer
wget -N https://raw.githubusercontent.com/bcmeter/bcmeter/main/install.sh && sudo bash install.sh

This runs an unattended installation taking a few minutes.

Current Platform (V2)

The V2 bcMeter comes with firmware pre-installed. Setup only requires:

Plug in power
Connect to the "bcMeter" WiFi hotspot
Open http://bcmeter-XXXX.local (XXXX = last 4 hex chars of MAC address)
Follow the Welcome Screen

See Setup for detailed instructions.

@@ Line 1: / Line 1: @@
-== Set Up the microSD Card ==
+{{Note|1='''Legacy V1 Documentation''' — This page documents software setup for the bcMeter V1. The current V2 bcMeter comes pre-configured and is set up via the [[Setup#Welcome Screen|Welcome Screen]]. These instructions are preserved for V1 users.}}
-.	Copy Image of [https://www.raspberrypi.org/software/operating-systems/#raspberry-pi-os-32-bit Raspberry Pi OS '''Lite'''] on your microSD card, Documentation for Linux / OSX in this file, for Windows use [https://www.raspberrypi.org/software/ this method] <br>
+== Recommended: Pre-configured microSD Card Image (V1) ==
-'''Make sure to download the Lite''' and '''not''' Desktop / Desktop and recommended software
-.	For Linux use the terminal to copy the image to the microSD card by this command:
+=== Step 1: Download and Flash the Image ===
-      dd if=path/to/image of=/dev/diskX bs=8m
-Replace path/to/image with path to image and diskX with deviceaddress of your microSD-card. Drag / drop the icon to the terminal is possible if in desktop environment.<br>
+# Download the bcMeter image file [https://bcmeter.org/wp-content/uploads/simple-file-list/bcMeter_latest_img.zip here]
+# Unzip the downloaded file
+# Use [https://www.balena.io/etcher/ Etcher] to flash the image to your microSD card:
+#* Insert your microSD card
+#* Open Etcher and select the image
+#* Select your microSD card as target
+#* Click "Flash!" and wait for completion
-Use rdiskX instead of diskX on OSX to accelerate the transfer
+=== Step 2: Boot and Connect ===
-== Configure the microSD Card for WiFi access ==
+# Insert the flashed microSD card into the Raspberry Pi
+# Power on the device
+# Wait approximately 2 minutes for boot
+# Connect to the WiFi network "'''bcMeter'''" with password: <code>bcMeterbcMeter</code>
-After the above steps, on Windows and OSX a new drive/partition named „boot“ is visible in Explorer or Finder. On Linux you see additionally rootfs, we can ignore this.
+=== Step 3: Configure ===
-.	Create a new and empty file just called „ssh“ on the new boot partition. This is just for enabling ssh as Raspberry OS evaluates this file to enable the ssh configuration.
+# Open a browser and navigate to <code><nowiki>http://bcmeter-XXXX.local</nowiki></code> (where XXXX are the last 4 hex characters of the MAC address, shown on the device label)
-You can simply do that in Linux/OSX by navigating to the /boot partition of the microSD Card and enter
+# The bcMeter interface will appear
-      nano ssh
+# Follow on-screen instructions
-Then just save the empty file and exit (ctrl+o for save, ctrl+x for exit)
+== Advanced: Manual Setup via SSH (V1) ==
-On Windows, open Notepad.exe and save the empty file as ssh on /boot. Double check in file properties that no .txt is added (but hidden)
+Use the [https://www.raspberrypi.com/software/ Raspberry Pi Imager] to write '''Raspberry OS 64-bit LITE''' to the microSD card. Do '''not''' install the Desktop variant.
+Configure with username <code>bcmeter</code> and password <code>bcmeter.org</code>. Enable SSH and WiFi.
-.	Using the same method as above, put a file called wpa_supplicant.conf  in the same partition (/boot). This contains the credentials needed to connect to your WiFi. Add as many Networks as you like.
+=== SSH Installation ===
-'''Be sure to edit the parameter „country“ correctly, else the pi may not be able to connect to your WiFi.'''
+<pre>
-Copy / paste the following. Make sure quotes are pasted correctly.
+ssh bcmeter@bcMeter
+# or: ssh bcmeter@bcMeter.local
-      ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev
+# Download and run installer
-      country=de
+wget -N https://raw.githubusercontent.com/bcmeter/bcmeter/main/install.sh && sudo bash install.sh
-      update_config=1
+</pre>
-      network={
-      ssid="YourWiFiName"
-      psk="Password"
-      }
+This runs an unattended installation taking a few minutes.
+== Current Platform (V2) ==
-Save the file and eject the microSD Card from the PC. This file will be removed from this place as soon as the raspberry has read it. If your Raspberry does not connect to your WiFi, you can repeat this process as often as necessary. If the file is still there after an attempted boot, there has something more severe gone wrong.
+The V2 bcMeter comes with firmware pre-installed. Setup only requires:
-== Configuring the Raspberry Pi to be a bcMeter ==
+# Plug in power
+# Connect to the "bcMeter" WiFi hotspot
+# Open <code><nowiki>http://bcmeter-XXXX.local</nowiki></code> (XXXX = last 4 hex chars of MAC address)
+# Follow the [[Setup#Welcome Screen|Welcome Screen]]
+See [[Setup]] for detailed instructions.
-.	Put microSD-Card in Raspberry and boot it up (takes up to a minute)
-Log into the raspberry via terminal on Linux/OSX
-      ssh pi@raspberrypi
-Or any terminal client on Windows (for example Putty) with the following default credentials
-address: raspberrypi
-login name: pi
-login passwort: raspberry
-'''(For some mobile hotspots it is required to add .local to the hostname (e.g. raspberryp.local). Try this first if no connection is possible.)'''
-.	Being logged in, enter
-       wget -N https://raw.githubusercontent.com/bcmeter/bcmeter/main/install.sh && sudo bash install.sh