Difference between revisions of "Assembly"
| Line 1: | Line 1: | ||
'''Requirements (not pictured): | |||
# Screwdriver | |||
'''Requirements (not pictured | |||
# Solder Iron | # Solder Iron | ||
# Solder | # Solder | ||
# Flux | # Flux | ||
# 3D Printer | # 3D Printer / 3d printing service | ||
''' | ''' | ||
[[File: | [[File:Overview.jpg|500px|left]]<br clear=all> | ||
Overview: | |||
A: Upper Case<br> | A: Upper Case<br> | ||
| Line 22: | Line 20: | ||
D: LED/Sensor holder<br><br> | D: LED/Sensor holder<br><br> | ||
E: LED/Sensor holder<br><br> | |||
F: PCB (Order from pcbway.com, jlcpcb.com or anywhere else (you will get 5 PCBs (minumum) for ~$20 with fast shipping) – find gerber files on github repository or bcmeter.org)<br> | |||
F: PCB from pcbway.com, jlcpcb.com or anywhere else (you will get 5 PCBs (minumum) for ~$20 with fast shipping) – find gerber files on github repository or bcmeter.org<br> | |||
G: Components from mouser.com or anywhere else (~60) – [https://www.mouser.de/ProjectManager/ProjectDetail.aspx?AccessID=0f6a28fa20 mouser shopping cart] or [[bill of material]] | G: Components from mouser.com or anywhere else (~60) – [https://www.mouser.de/ProjectManager/ProjectDetail.aspx?AccessID=0f6a28fa20 mouser shopping cart] or [[bill of material]] | ||
| Line 45: | Line 41: | ||
200g Resin / FDM ~ $5-$10<br> | 200g Resin / FDM ~ $5-$10<br> | ||
[[File:Bcmeter-general-purpose-case.jpg|500px|left]]<br clear=all> | |||
Assembly Instructions<br> | Assembly Instructions<br> | ||
Revision as of 17:15, 7 July 2021
Requirements (not pictured):
- Screwdriver
- Solder Iron
- Solder
- Flux
- 3D Printer / 3d printing service
Overview:
A: Upper Case
B: Lower Case
C: Intake manifold
D: LED/Sensor holder
E: LED/Sensor holder
F: PCB (Order from pcbway.com, jlcpcb.com or anywhere else (you will get 5 PCBs (minumum) for ~$20 with fast shipping) – find gerber files on github repository or bcmeter.org)
G: Components from mouser.com or anywhere else (~60) – mouser shopping cart or bill of material
H: Order filter papers (~$50) – Pack of 50 sufficient for at least 1000 samples. Type TBD, tested with T60A20 – ask local labs for availability
I: Additional material:
- Hot Glue ~$7
- Rubber band (SHORE A) for sealing ~$11
- M3 Screws ~$3
- M3 threads ~$7
- microSD Card (4gb+)
40 Pin Header (optional for plug the Hat) J: Order membrane pump (~$160) - here (TBD – cheaper solution may be available soon)
STL for 3D Printing (SLA or FDM) attached. Print on any 3d printer or send to any service provider. Use black filament / resin. If possible, use flex filament or mix resin with flex resin.
200g Resin / FDM ~ $5-$10
Assembly Instructions
Current version is designed for absolute simplicity so as little as possible SMD components and parts with large footprints are used. Start assembling by soldering the smalles parts first (MMBT3904 + MCP3426). Then add THT passive parts piece by piece according to description on the PCB and the BOM.
- Place IRL81A (IR Emitter) and LPT80A (Sensor) in adapters D and E, seal with hot glue and solder wires to the corresponding vias on the PCB. Long leg is anode (positive).
- Place adapters D and E in the case A and B. Emitter to top case. Seal with (hot) glue or tape.
- Put pump in place and do a test run for leakage.
